Categories
Baxter UE1322D – 0.9% Sodium Chloride Injection, USP, 250 mL VIAFLO Plastic Container, 30/CS
Baxter UE1322D – 0.9% Sodium Chloride Injection, USP, 250 mL VIAFLO Plastic Container, 30/CS
Baxter UE1322D Sodium Chloride Injection, USP in VIAFLO Plastic Container
Sodium Chloride Injection, USP is a sterile, nonpyrogenic solution for fluid and electrolyte replenishment in single dose containers for intravenous administration. It contains no antimicrobial agents. The nominal pH is 5.0 (4.5 to 7.0). Composition, osmolarity, and ionic concentration are shown below:
0.9% Sodium Chloride Injection, USP contains 9 g/L Sodium Chloride, USP (NaCl) with an osmolarity of 308 mOsmol/L (calc). It contains 154 mEq/L sodium and 154 mEq/L chloride.
VIAFLO is a flexible plastic container fabricated from a multilayer sheeting (PL-2442) composed of Polypropylene (PP), Polyamide (PA) and Polyethylene (PE). The amount of water that can permeate from inside the container into the overwrap is insufficient to affect the solution significantly. Two different administration connectors are available with VIAFLO containers. The VIAFLO dripless access container (DAC) will not drip once the spike is removed. The non-DAC VIAFLO will drip once the spike is removed from the administration port.
VIAFLO is not made with natural rubber latex, DEHP, or PVC.
Baxter UE1322D Clinical Pharmacology
Sodium Chloride Injection, USP has value as a source of water and electrolytes. It is capable of inducing diuresis depending on the clinical condition of the patient.
Indications and Usage of Baxter UE1322D
Sodium Chloride Injection, USP is indicated as a source of water and electrolytes. 0.9% Sodium Chloride Injection, USP is also indicated for use as a priming solution in hemodialysis procedures.
Directions for Use of VIAFLO Plastic Container
To Open
Tear overwrap down side at slit and remove solution container. Visually inspect the container. If the outlet port protector is damaged, detached, or not present, discard container as solution path sterility may be impaired. Some opacity of the plastic due to moisture absorption during the sterilization process may be observed. This is normal and does not affect the solution quality or safety. The opacity will diminish gradually. Check for minute leaks by squeezing inner bag firmly. If leaks are found, discard solution as sterility may be impaired. If supplemental medication is desired, follow directions below.
- Remove the container from the over wrap just before use.
- Check for minute leaks by squeezing inner bag firmly. If leaks are found, discard solution, as sterility may be impaired.
- Check solution for clarity and absence of foreign matter. If solution is not clear or contains foreign matter, discard the solution.
Preparation for Administration
- Suspend container from eyelet support.
- Remove plastic protector from outlet port at bottom of container.
- Grip the small wing on the neck of the port with one hand,
- grip the large wing on the cap with the other hand and twist,
- the cap will pop off.
- Use an aseptic method to set up the infusion.
- Attach administration set. Refer to directions accompanying set for connection, priming of the set and administration of the solution.
To Add Medication
Additives may be incompatible.
To add medication before solution administration
- Prepare medication site.
- Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.
- Mix solution and medication thoroughly. For high density medication such as potassium chloride, tap ports gently while ports are upright and mix thoroughly.
To add medication during solution administration
- Close clamp on the set.
- Prepare medication site.
- Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.
- Remove container from IV pole and/or turn to an upright position.
- Evacuate both ports by tapping them gently while container is in the upright position.
- Mix solution and medication thoroughly.
- Return container to in-use position and continue administration.